Instructor: Matt Hayden
Matt Hayden (@matthaydenwelder) runs the welding career tech program at Cedartown High School in Georgia. His program is one of the best in the country, going to state and national championships pretty much every year. His classes boast students who are already making a good living for themselves, some of whom haven't even graduated! If you're looking to learn the ropes and you need someone who can teach you with maximum clarity and efficacy, look no further than Matt Hayden.
-
Matt Hayden - Tig Hot Pass 1G plate
Tig Hot Pass 1G plate
-
Matt Hayden - 1G Plate Root pass w/Dry Rig Tig
1G Plate Root pass w/Dry Rig Tig
-
Matt Hayden - Intro to a Dry Rig for TIG
TIG on plate open root with a dry rig
-
Matt Hayden - Fill and cap 3G plate 7018
Fill and cap 3G plate 7018
-
Matt Hayden - 6010 Root Pass on 3G Plate
6010 Root Pass on 3G Plate
-
Matt Hayden - Pulse GMAW Vertical 3G Plate Part 4
3G plate with a backing strip 1/4" gap on 3/8" plate using pulse MIG!
-
Matt Hayden - 3F Pulse GMAW Part 3
3F Pulse GMAW Part 3
-
Matt Hayden - 2G Pulse Plate Test Part 2
2G Pulse Plate Test Part 2. 3/8" Inch plate 1/4" inch gap and backing. ER70s6 wire. 230 ipm wire speed. Pulse Spray MIG trim set to 1.05. Lincoln S350 pulse spray program #12.
-
Matt Hayden - Pulse Spray MIG 2F Tee Joint Part 1
In this video Matt welds a 2f tee joint fillet weld using pulse spray mig using .035" ER70S6 wire at 425 ipm
-
Matt Hayden 2F Spray with 90-10 Gas
Horizontal 2F position on a tee joint
-
Matt Hayden - 1G Spray Arc with 90-10 gas
1G Test Plate with Spray Arc...A common test for some of the local industry close to me
90/10 argon/co2 is a fairly commonly used blend for spray transfer mig and also works for pulse spray.
For this 1G test plate we used .035" ER70S6 wire
Settings were dialed in using a simple 2f tee joint in o... -
Matt Hayden - 7018 Vertical Uphill Padding
Vertical uphill technique
-
Matt Hayden - 7018 DCEP, DCEN Long Arc
A quick video with 7018 DCEP, DCEN, and it's effect on a long arc
-
Matt Hayden - 7018 Horizontal Padding Plate
Horizontal Padding Plate with 7018, 125 Amps DCEP
-
Matt Hayden - Overhead Roof Top 7018 1/8" stringers
Matt Hayden - 4F tee joint Rooftop Overhead SMAW Stick welding 7018 1/8" stringers. Great practice for controlling the puddle in overhead position
-
Matt Hayden Stick Welding Overhead Roof Top Weave 7018 1/8"
Matt Hayden Stick Welding Overhead Roof Top Weave 7018 1/8"
-
Matt Hayden - Stick Welding overhead Roof Top Weave with 7018 3/32
Stick Welding overhead Roof Top Weave with 7018 3/32 tips and arc shots from Matt
-
Matt Hayden - Rooftop OVERHEAD 7018 3/32 Stringers
What are rooftop welds? Let's talk about it...
-
Matt Hayden - Vertical 6010 Uphill Padding -stick welding
Vertical 6010 Uphill Padding
-
Matt Hayden - Horizontal 6010 Padding- stick welding
Horizontal 6010 Padding tips and arc shots with Matt
-
Matt Hayden - 6010 Flat Padding - stick welding
1/8" 6010 flat padding on 1/4" mild steel
-
Matt Hayden - GMAW MIG - 2F Spray transfer with 80-20 Gas
Can you Spray Arc with 80-20 gas? Yes
-
Matt Hayden - Talking Spray Arc with Jody and Matt
Matt and Jody talk about Spray Arc and how local industry utilizes it. Difference between spray arc and short circuit.
-
Matt Hayden - Oxygen Propane
Torch lighting and flame adjusting are somewhat different when using propane as fuel gas.
Matt Hayden gives a demonstration of setup, torch lighting, and shutdown using oxygen and propane.